|
|
|
| | EPX36 is a two-component high-solid self-leveling epoxy coating designed mainly for coating industrial floors | | |
| | Designed mainly for floor protection, used with suitable primer, on well-prepared cement floors to give hard wearing, water, chemical and abrasion-resistant coat that is resistant to bacterial growth. Typical uses are in hospitals, operating rooms, laboratories, chemical plants (textiles factories, laundries, …), food and pharmaceutical industries, clean rooms, stores, cold rooms, restaurants, industrial kitchens, galleries, showrooms,… etc, and in all installations that require moderate traffic on plant floor. | | |
| • Can be applied on damp concrete.
• Economical and glossy industrial floor coating.
• Excellent abrasion resistance.
• Excellent resistance to water and sea water even in permanent wet areas.
• Excellent resistance to the growth of bacteria, fungi, and algae.
• Excellent resistance to salt solutions, acids, alkalis, desinfectants, detergents, white spirits, mineral oils, fatty oils, crude oil, fuels and a wide range of industrial chemicals. (A separate leaflet CHR01 is available).
• Coat thicknesses ranging from 0.5 to 1 mm can be applied.
• Available in various colours to provide attractive floor finish. It is also suitable for use as for marking or warning areas.
• Easy and low-cost maintenance.
• Good anti-slip resistance.
| | |
| | • Method of Application : | Roller | | • Mixing Ratio : | (by volume) 3.6 to 0.75 (A to B). | | • Mixing : | The individual components should be thoroughly stirred before the two are mixed together. Combine components (A & B) in supplied proportions and mix thoroughly using a slow speed mixer for at least 3 minutes to achieve uniform consistency; “DO NOT USE HIGH SPEED MIXER”. Never mix more material than can be used within potlife. Material that has begun to set must be discarded. | | • Thinner / Cleaner : | S405 “known as Epoxsol” is used for thinning or cleaning. Mixing ratio with thinner depends mainly on temperature and on method of application. For example: At 20°C airless spray or roller application will need approx 15% by volume thinner S405. | | • Note : | • When recoating, a special attention should be given toward drying times “minimum & maximum recoating time”. Any delay in applying interval coats may request sanding the surface of the previous coat to insure good adhesion. • The reaction between the epoxy and its curing agent (A & B) can not be guaranteed unless a temperature of at least 10°C is maintained for the mixture and the substrate until complete curing. Temperature of substrate should be at least 3°C above dew point to avoid moisture condensation during application. • Coated surfaces by EPX36 should not be exposed to water, chemicals, or mechanical stresses before it is fully cured. |
| | |
| | • Component B : | CAT41 | | • Color : | Available in major industrial colors using color mixing instrument Azmix | | • Gloss : | Gloss (ASTM-D523). | | • Volume Solids : | 94.4 % (ASTM-D2697). | | • VOC : | 48 g/L (ASTM-D3960). | | • Flexibility : | Very good | | • Recommended film thickness : | 500-1000 microns “dry”. | | • Theoretical spreading rate : | 1.9 m²/L at 500 microns “dry”. | | • Water resistance : | Excellent | | • Abrasian Resistance : | Excellent | | • Chemical Resistance : | Very good. (A separate leaflet CHR01 is available) | | • Solvent Resistance : | Good. (A separate leaflet CHR01 is available) | | • Number of Coats : | 1-2 | | • Specific Gravity (mixed) : | 1.60 kg/L (ASTM-D1475). | | • Packaging : | Component A “base” : 3.6 L in metal can. Component B “drier: CAT41” : 0.75 L in metal can . |
| | |
| Proper surface preparation is essential to ensure coating success, performance, and longevity. In general, all surfaces must be clean, dry, undamaged, and free of contaminants prior to application.
CONCRETE
• New concrete: Must be cured for at least 28 days at 21°C and 50% RH, or for an equivalent duration based on temperature and humidity.
EPX17 primer may be applied once the concrete has cured for at least 14 days at 21°C and 70% RH.
• Old concrete: Remove surface irregularities such as fins and protrusions by stoning, sanding, or grinding.
Abrasive blasting is the most effective method to remove previous coatings, form oils, laitance, and other foreign matter.
• Fill small holes and voids with STOP200 before applying EPX36.
• For highly porous concrete or poorly ventilated areas where solvent vapors are a concern, EPX17 is recommended as the primer.
• If the concrete substrate exhibits a moisture content greater than 50%, application of EPX17 is recommended.
• If the surface has low absorption, EPX02 is a more suitable choice. | | |
| | • Dry to Touch : | 3 hours (ASTM-D1640). | | • Dry to Handle : | 24 hours “minimum recoat time”, 2 days ”maximum recoat time” (ASTM-D1640). | | • Fully Cured : | 7 days | | • Note : | Drying times can be affected by many factors such as temperature, ventilation and coat thickness. Higher temperatures will shorten the drying times |
| | |
| • Epoxy system, in general, especially component B, has to be kept in a cool and well ventilated place, protected from heat and direct sunlight. EPX36 is considered as being flammable material.
• Shelf life is two years from packing date in unopened original containers at 10 to 40°C. Containers should be kept tightly closed.
Safety:
• Well ventilated conditions should be provided during application.
• Do not breathe or inhale mist.
• Wear air-mask and avoid skin or eye contact.
| |
|
|
|
|
information in this data sheet and in all our data sheets are given to the best
of our knowledge based on laboratory testing and practical experience. Final results
depend on following instructions and on consumer skill. Our responsibility is limited
to providing products that Conform to samples and specimens provided by us. Due
to technical needs, we reserve the right to change any given specification without
notice.
|
|
|
