|
|
|
|
|
| | Water based acrylic decorative finishing material (Stucco). | | |
| | Used mainly on well prepared concrete, wood, and gypsum board substrates. Highly recommended for the decoration of hotels, restaurants, villas, palaces, and in all places that require a distinguished decorative aspect. | | |
| • Produces finishes offering numerous colorful decorative solutions with excellent properties in a short period of time.
• Easy to apply, single component “no mixing required”.
• Can be applied to vertical and overhead surfaces without slumping.
• No harmful vapors and scents are present (makes it easy to use and to apply in confined areas).
| | |
| | • Method of Application : | Anticorrosive stainless steel trowel. | | • Thinner / Cleaner : | In general, there is no need to dilute. Clean applying tools immediately
after application is completed by water.
| | • Application Temperature : | 10-40?C. | | • Note : | • When recoating a special attention should be given toward drying times. |
| | |
| | • Color : | White, international colors such as E-Standard, NCS, and RAL using tinting machine. | | • Volume Solids : | 52.2 % (ASTM-D2697) | | • VOC : | 0 g/L (ASTM-D3960) | | • Flexibility : | Good | | • Adhesion : | Excellent | | • Recommended film thickness : | 200 microns “dry” | | • Theoretical spreading rate : | 2.61 m²/L at 200 microns “dry” | | • Specific gravity : | 1.55 Kg/L (ASTM-D1475). | | • Water resistance : | Good | | • Number of Coats : | 2-4 | | • Packaging : | 0.9 L in plastic container or 3.6 L in metal can. |
| | |
| Coating performance is, in general, proportional to the degree of surface preparation. Surface must be clean and free of dust and other contaminants prior to application.
A- Wall Preparation:
Walls should be prepared prior to applying WT12 (Stucco):
1- Uncoated and clean walls:
Prepare the surface in accordance with the application instructions for the suitable primer and / or filler being used (Primer: WT01, Filler: WT03 or WT02 for higher thicknesses). Then apply WT05 after being sure that all blow holes and defects are completely filled to produce a smooth, clean and level surface. When filling deep holes, it is recommended to apply STOP200 (refer to its technical leaflet).
2- Previously coated walls:
WT05 should be applied to existing coatings. The surface of the existing coating has to be cleaned and abraded (especially when coating occurs over oil-based coatings). Be sure that WT05 adheres well to the existing coating prior to application to ensure good adhesion properties.
B- Application steps of WT12 (Stucco):
1- Apply WT12 by a stainless steel trowel to the entire surface to be decorated in a way to achieve the desired shape.
2- Smooth surface evenly and remove any loose materials from the surface with stainless steel trowel. The angle between the substrate and the spatula should be approximately 15 degree.
3- After drying of the final coat, a polish could be applied to bring out the shine and the rich marble like effect of the wall.
| | |
| | • Dry to Touch : | 30 minutes (ASTM-D1640). | | • Dry to Handle : | 12 hours “minimum recoat time” (ASTM-D1640). | | • Note : | Drying times can be affected by many factors such as temperature, ventilation and coat thickness. Higher
temperatures will shorten the drying times.
|
| | |
| • WT12 must not be allowed to come into contact with non treated metals that are likely to corrode. Containers must be kept tightly closed. Exposure to strong heat and frost must be avoided.
• Shelf life is two years from packing date in unopened original containers at 10 to 40°C. Containers should be kept tightly closed.
Safety:
• Avoid skin or eye contact. Prolonged contact may cause irritation of the skin and mucous membranes.
| |
|
|
|
|
information in this data sheet and in all our data sheets are given to the best
of our knowledge based on laboratory testing and practical experience. Final results
depend on following instructions and on consumer skill. Our responsibility is limited
to providing products that Conform to samples and specimens provided by us. Due
to technical needs, we reserve the right to change any given specification without
notice.
|
|
|
