|
|
|
|
|
| | ACR Concrete Sealer is a solvent based acrylic concrete floor sealer. | | |
| | Used to protect and seal all properly prepared interior and exterior concrete floors and landscapes including garage floors. ACR Concrete Sealer is an easily applied material which protects and beautifies concrete floors above or below grade | | |
| 1- Easy to apply.
2- Provides UV and abrasion resistant film.
3- Seals and protects concrete surfaces from moisture penetration, staining, dirt, dust, and wear.
4- Impervious to water, grease, petroleum oils, salt and other common chemicals.
5- Excellent for sealing and protecting concrete landscapes and garage floors .
6- Tough and flexible film, bridges hairline cracks.
7- Quick drying and easily recoated. | | |
| | • Method of Application : | Conventional spray, brush, or roller. | | • Mixing : | Stir well before application in order to ensure that a uniform consistency is achieved. | | • Cleaner : | S304 is used for thinning and cleaning. Mixing ratio with thinner will need approx. 100% by volume thinner S304 (1 volume S304 to 1 volume ACR Concrete Sealer). The higher the temperature the less the needed dilution. | | • Application Temperature : | 10-40° |
| | |
| | • Color : | Clear | | • Gloss : | Semi-Gloss (ASTM-D523) | | • Volume Solids : | 47 % (ASTM-D2697) | | • Flexibility : | Excellent | | • Recommended film thickness : | 100 microns “dry”. | | • Theoretical spreading rate : | 4.7 m²/L at 100 microns “dry” | | • Specific gravity : | 0.995 kg/L (ASTM-D1475). | | • Water resistance : | Excellent | | • Number of Coats : | 2 | | • Packaging : | 3.6 L in US Gallon or 16 L in metal can. |
| | |
| Coating performance is, in general, proportional to the degree of surface preparation. Surface must be clean, dry or damp but not wet and free of oil, grease and other contaminants prior to coating.
Remove fins and other protrusions by stoning, sanding or grinding.
New concrete: Must be cured at least 28 days at 21?C and 50% RH, or equivalent time.
Old concrete : Abrasive blasting is best to remove all previous coatings, form oils, laitance and other foreign matter. Fill small holes or voids with STOP200 before applying ACR Concrete Sealer.
Notes:
Surfaces coated by ACR Concrete Sealer can be cleaned with neutral detergents using a rotary scrubbing machine to extend its service life.
In highly trafficked areas it is recommended to overcoat ACR Concrete Sealer by a suitable finishing coat. | | |
| | • Dry to Touch : | 30 minutes (ASTM-D1640). | | • Dry to Handle : | 2 hours "minimum recoat time" 4 hours "maximum recoat time (ASTM-D1640). |
| | |
| ACR Concrete Sealer has to be kept in a cool and well-ventilated place, protected from heat and direct sunlight. ACR Sealer is classified under highly flammable materials.
Shelf life is two years from packing date in unopened original containers at 5 to 40°C. Containers should be kept tightly closed.
Safety:
1- Well-ventilated conditions should be provided during application.
2- Do not breathe or inhale mist.
3- Wear air mask and avoid skin or eye contact. | |
|
|
|
|
information in this data sheet and in all our data sheets are given to the best
of our knowledge based on laboratory testing and practical experience. Final results
depend on following instructions and on consumer skill. Our responsibility is limited
to providing products that Conform to samples and specimens provided by us. Due
to technical needs, we reserve the right to change any given specification without
notice.
|
|
|
