|
|
|
|
|
| | WT08 is a water emulsion acrylic finishing coat. | | |
| | As a finishing coat applied over WT05, highly recommended for coating exterior and interior building structures and for all decorative purposes. | | |
| • Excellent flow properties (without brush marking)
• Excellent resistance to water, detergent and saponification.
• Highly resistant to the effects of ultra-violet light and weathering.
• Excellent adhesion and flexibility.
• Excellent hiding power and short drying times, reducing application times considerably.
• Easy to clean, economical and low cost maintenance.
• Odor free, used in all areas where solvent based coatings are prevented.
• Wide range of colors can be obtained to suit all tastes and requirements by using tinting machines.
• Available as an anti-bacterial coat from approved distributors.
WT08 is highly recommended to be used for decoration of interior walls under the decorative materials Marble ALK or Marble AQ.
| | |
| | • Method of Application : | Suitable brush, roller or airless spray (It is not recommended to use synthetic bristle large surface paint brush). | | • Mixing : | Stir well before application in order to ensure that a uniform consistency
is achieved.
| | • Thinner / Cleaner : | Water is used for thinning or cleaning. Mixing ratio with water depends
on method of application.
No dilution is required when airless spray is used at 20°C, other method of application (roller, brush) will need up to 15% approx. by volume water.
| | • Application Temperature : | 10-40?C. | | • Note : | When recoating, a special attention should be given toward drying times. |
| | |
| | • Color : | White or upon request using tinting machine. | | • Gloss : | Matt (ASTM-D523) | | • Volume Solids : | 35.3 % (ASTM-D2697) | | • VOC : | 14.4 g/L (ASTM-D3960) | | • Flexibility : | Excellent. | | • Recommended film thickness : | 50 microns “dry” | | • Theoretical spreading rate : | 7.1 m²/L at 50 microns “dry” | | • Specific gravity : | 1.32 kg/L (ASTM-D1475) | | • Water resistance : | Excellent. | | • Washability : | Excellent. | | • Abrasian Resistance : | Good. | | • Number of Coats : | 2 | | • Packaging : | 3.6L in metal or 3 usg in plastic pail 11.36 L±3% or 20 Kg in plastic pail. |
| | |
| Coating performance is, in general, proportional to the degree of surface preparation. Surface must be clean, undamaged and free of oil, grease and other contaminants prior to coating.
It is recommended to apply WT08 over WT05 (refer to its technical leaflet).
Prepare surface in accordance with application instructions for the suitable undercoat being used (WT05). WT05 should be left to achieve a tack-free condition prior to applying WT08. Be sure WT05 is clean, dry and free of oil, grease and other contaminants when WT08 is applied.
Do not apply WT08 to existing coatings (oil-based or water-based) without further surface preparation such as cleaning, abrading and leveling the surface with “WT03” if required, and applying a suitable undercoat “WT05”.
| | |
| | • Dry to Touch : | 20 minutes (ASTM-D1640). | | • Dry to Handle : | 1 hour “minimum recoat time” (ASTM-D1640). | | • Note : | Drying times can be affected by many factors such as temperature, ventilation and coat thickness.
Higher temperatures will shorten the drying times. |
| | |
| • WT08 must not be allowed to be stored in untreated metals that are likely to corrode. Containers must be kept tightly closed. Exposure to strong heat and frost must be avoided.
• Shelf life is two years from packing date in unopened original containers at 10 to 40°C. Containers should be kept tightly closed.
Safety:
Avoid skin or eye contact. Prolonged contact may cause irritation of the skin and mucous membranes.
| |
|
|
|
|
information in this data sheet and in all our data sheets are given to the best
of our knowledge based on laboratory testing and practical experience. Final results
depend on following instructions and on consumer skill. Our responsibility is limited
to providing products that Conform to samples and specimens provided by us. Due
to technical needs, we reserve the right to change any given specification without
notice.
|
|
|
